Search found 1163 matches

by Roberts_Clif
April 20th, 2021, 7:51 am
Forum: Help me fix this print!
Topic: Strange pip on outside of print
Replies: 5
Views: 29

Re: Strange pip on outside of print

On Cura slicers you have a function that allows a random start print location called Z-Seam alignment.
Though if you choose this random function it creates more travel moves.
by Roberts_Clif
April 18th, 2021, 9:59 am
Forum: General 3D Printing Conversation
Topic: First eight or nine layers are mush
Replies: 1
Views: 77

Re: First eight or nine layers are mush

We could use a lot more information please!

Which slicer are you using?
What is the slicer's setting?
Posting a photo of this bulging rim/lip will greatly help, because seeing is better than reading.

I would check the setting to see if you have inadvertently enabled the skirt function.
by Roberts_Clif
April 14th, 2021, 7:59 pm
Forum: Software and Firmware Discussion
Topic: Klipper with Hictop 08 ?
Replies: 5
Views: 379

Re: Klipper with Hictop 08 ?

pins_RAMPS.h Attached
pins_RAMPS.h
(16.08 KiB) Downloaded 4 times
Is there a specific reason you want to use Klipper.
I have configured most of Marlin 1.x.x and Marlin 2.x.x to work with Hictop 3DP08
by Roberts_Clif
April 14th, 2021, 8:41 am
Forum: Software and Firmware Discussion
Topic: Klipper with Hictop 08 ?
Replies: 5
Views: 379

Re: Klipper with Hictop 08 ?

Hello: I Have two Hictop a 3DP11 and 3DP12 however I have never used Klipper. Though I have setup many version of marlin for your Hictop 3DP08 3DPrinter, an could use My configuration files for Marlin to give you the pins. The controller for your 3DP08 is the same on both the Hictop 3DP11 and 3DP12 ...
by Roberts_Clif
April 8th, 2021, 7:23 am
Forum: Cura
Topic: Issue with printing, sliced with Cura
Replies: 5
Views: 545

Re: Issue with printing, sliced with Cura

Do not know if this is a solution or not, here goes.

I have printed most recent models with PrusaSlicer 2.3.0 it is more complex to setup though the printed model show results.
I still use Cura for other models that need less perfection.
by Roberts_Clif
April 5th, 2021, 6:55 pm
Forum: Cura
Topic: Issue with printing, sliced with Cura
Replies: 5
Views: 545

Re: Issue with printing, sliced with Cura

This is quite a frequent problem with Cura and happens quite often.
when any change happens on Z-Axis, could be many changes to the shape of the model, the outcome is always the same style texture surface change.


Look at this example
Right Lead-Screw comparison.jpg
by Roberts_Clif
March 22nd, 2021, 12:49 pm
Forum: General Discussion
Topic: What are you printing lately?
Replies: 6
Views: 1196

Re: What are you printing lately?

cam clip 3.0

I found this great little bag clip and have been printing several for every member of the family.
by Roberts_Clif
February 26th, 2021, 7:48 am
Forum: Off Topics!
Topic: Logo help for my new project
Replies: 8
Views: 10795

Re: Logo help for my new project

DavidLu45 wrote:
February 26th, 2021, 3:31 am
Are these sources reliable for choosing a 3d printer? [/url].
I would say they are Incomplete!
This being said the answer is they show only a small spectrum of the available 3D Printers.
These list do not have a single 3D Printer that I would have chosen for my forth 3D Printer for my workshop.
by Roberts_Clif
February 20th, 2021, 8:08 am
Forum: Hardware Modifications
Topic: 3DP11/12
Replies: 0
Views: 1041

3DP11/12

Have been quite busy lately of course everyone else has been to. Hope to Get back and start working on some upgrades, I have been wanting to upgrade my inductive Proximity sensors power. For as long as I have owned my 3D Printers I have operated all proximity sensors with a +5volt source. I plan to ...
by Roberts_Clif
February 12th, 2021, 1:24 pm
Forum: Help me fix this print!
Topic: Anycubic i3 Mega - Stencil print
Replies: 8
Views: 1801

Re: Anycubic i3 Mega - Stencil print

I print using PLA at the below settings for first layer only Settings in Cura: Temp: 200-210 °C (no difference) speed: 32-50 mm/s Heatbed temp.: 52-56°C Layer height: 0.15 mm Then change the print speed to speed: 72-86 mm/s P.S. have the same logo on my print bed surface
by Roberts_Clif
February 8th, 2021, 9:32 am
Forum: Resin 3D Printers
Topic: Alright Resin Gurus...top tips for beginners?
Replies: 7
Views: 1040

Re: Alright Resin Gurus...top tips for beginners?

I would much like to learn though know little about resin printers.

Though am a member of 5 other 3D Printer forums an if you need help message or post me, I can re-post to them an get help for you.
by Roberts_Clif
February 2nd, 2021, 5:42 pm
Forum: General Discussion
Topic: It got really quiet in here...how can we fix that?
Replies: 7
Views: 2088

Re: It got really quiet in here...how can we fix that?

I have been using these sense beginning 3D Printing. An still can not tell you if they remove moisture from filament. A soon as the filament waterproof package is opened they are then placed in a container with a moisture Eliminator. I live in the Channeled Scablands of eastern Washington a desert t...
by Roberts_Clif
February 2nd, 2021, 7:50 am
Forum: General Discussion
Topic: It got really quiet in here...how can we fix that?
Replies: 7
Views: 2088

Re: It got really quiet in here...how can we fix that?

Without using moisture Eliminator I would have to make or purchase a filament dryer.
Though have kept my filament about 14 rolls in every large storage container with one, replacing every 6 months.

These are found at my local dollar stores.
Moisture Eliminator.jpg
by Roberts_Clif
February 1st, 2021, 4:07 pm
Forum: Help me fix this print!
Topic: Bad Surface
Replies: 1
Views: 411

Re: Bad Surface

Try This

Go to advanced search