Search found 740 matches

by Roberts_Clif
June 15th, 2019, 7:51 am
Forum: RepRap Printers
Topic: A long sad tale...
Replies: 8
Views: 95

Re: A long sad tale...

The voltage is a result of the 3.3volt supply an R1 Trim pot on the 3.3v supply this reference voltage an could exist, Vref could still be adjusted with a bad driver Chip.

Sample of a DRV8825 Driver module

0J4222.600.jpg
by Roberts_Clif
June 13th, 2019, 7:58 am
Forum: RepRap Printers
Topic: A long sad tale...
Replies: 8
Views: 95

Re: A long sad tale...

GrueMaster wrote:
June 12th, 2019, 10:20 pm
Since X & Y work, try swapping X or Y with Z. After swap, just move the two axis independently.

This is one that usually skips my mine as my Controller do not have removable Stepper Motor driver Modules.

Though I will be remembering as I just Purchased a Arduino with the Ramps 1.6
by Roberts_Clif
June 12th, 2019, 7:34 pm
Forum: RepRap Printers
Topic: A long sad tale...
Replies: 8
Views: 95

Re: A long sad tale...

It could be a bad Driver, Bad controller, Bad Stepper Motor Cable, it could be a Bad Stepper Motor. It could also be the Z-Axis feed rate as you have recently upgraded firmware to Marlin 1.1.9BF #define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 } Got jhansx here and now going in circles could use help ...
by Roberts_Clif
June 11th, 2019, 5:18 pm
Forum: General 3D Printing Conversation
Topic: Nova Hotend
Replies: 3
Views: 238

Re: Nova Hotend

LePaul wrote:
June 11th, 2019, 10:02 am
I haven't looked at it...I've been drooling over the Slice Engineering Mosquito lately
Well that also looks good with having a 50watt cartridge.
by Roberts_Clif
June 11th, 2019, 5:15 pm
Forum: Firmware
Topic: Marlin 1.1.9 full menus
Replies: 3
Views: 549

Re: Marlin 1.1.9 full menus

Thought you had though I ran across this Post and wanted to inquire.
by Roberts_Clif
June 11th, 2019, 5:14 pm
Forum: General 3D Printing Conversation
Topic: STL Preview Thumbnails
Replies: 7
Views: 216

Re: STL Preview Thumbnails

Ok!

I have worked with computers a long long time and sometimes things just go right for me.
by Roberts_Clif
June 11th, 2019, 9:58 am
Forum: General 3D Printing Conversation
Topic: Nut and bolt 3D printed
Replies: 1
Views: 200

Re: Nut and bolt 3D printed

He Lez0

I have 3D Printed a Table vise though the screw is 12.5mm is work ok.
by Roberts_Clif
June 11th, 2019, 9:55 am
Forum: General 3D Printing Conversation
Topic: Nova Hotend
Replies: 3
Views: 238

Re: Nova Hotend

No comments on this Nova multi wattage Heater Hotend.
by Roberts_Clif
June 11th, 2019, 9:52 am
Forum: Firmware
Topic: Marlin 1.1.9 full menus
Replies: 3
Views: 549

Re: Marlin 1.1.9 full menus

Hi LePaul

Not sure exactly what you are requesting.

Though Babystepping is in Configuration.adv.h and will display when enabled.

#define BABYSTEPPING
by Roberts_Clif
June 11th, 2019, 7:20 am
Forum: General 3D Printing Conversation
Topic: STL Preview Thumbnails
Replies: 7
Views: 216

STL Preview Thumbnails

HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Policies\System\EnableLUA exists
Image2.jpg
EnableLUA exists on system, and it is 0
by Roberts_Clif
June 10th, 2019, 9:33 am
Forum: General 3D Printing Conversation
Topic: STL Preview Thumbnails
Replies: 7
Views: 216

Re: STL Preview Thumbnails

I have UAC turned off in Windows 7 Pro and Windows 8 Pro have never had any problems.
Will let you know if one arrives?
by Roberts_Clif
June 7th, 2019, 7:59 pm
Forum: Large Scale 3D Printers
Topic: V1 Engineering's Piper
Replies: 31
Views: 1033

Re: V1 Engineering's Piper

Today I received the five steppers, and setup a Ramps controller test, decided to start with a V-Ref of .450
Setup all steppers an preformed simple moves on X, Y, Z E0 an E1 drivers functioning at my test current..
by Roberts_Clif
June 6th, 2019, 9:38 pm
Forum: Large Scale 3D Printers
Topic: V1 Engineering's Piper
Replies: 31
Views: 1033

Re: V1 Engineering's Piper

Today received the Arduino controller the Ramps 1.6 with five A4988 drivers modules. Decided to upload a known Firmware Marlin 1.1.5 to test the the basics, found that I needed a CH34X driver before it would allow an upload. Marlin 1.1.5 with the controller an Ramps 1.6 an drivers modules boots, how...
by Roberts_Clif
June 5th, 2019, 7:42 pm
Forum: News and Announcements
Topic: Testing out a new style!
Replies: 13
Views: 461

Re: Testing out a new style!

I have a question?

Most sites after I sign in the 2nd time the login appears in a drop down box, this site is the exception.
Here I have to type the full login every time suggested logins do not appear does any one know why...
by Roberts_Clif
June 5th, 2019, 10:17 am
Forum: ABS Filament General Discussion
Topic: 1st Failed ABS Model
Replies: 0
Views: 91

1st Failed ABS Model

Today I had my first failed ABS print. Although it was defiantly my fault, was still a my first failed ABS Print, now this was a simple error on my part. As I was in a hurry to print the model I forgot it was sliced for PLA an not for ABS, so I was printing an ABS model at PLA temperatures, below is...

Go to advanced search