Search found 10 matches
- January 4th, 2019, 11:33 pm
- Forum: General Questions
- Topic: Extruder wont extrude Hitop 3DP12
- Replies: 38
- Views: 45701
Re: Extruder wont extrude Hitop 3DP12
Spoke too soon. on my third part another heater died. It has 24V going to it, just cold. Is this normal?
- January 4th, 2019, 11:03 pm
- Forum: General Questions
- Topic: Extruder wont extrude Hitop 3DP12
- Replies: 38
- Views: 45701
Re: Extruder wont extrude Hitop 3DP12
Success. Finally after 3 new stepper motors and 2 new heaters a "good" part!
- January 2nd, 2019, 9:57 pm
- Forum: General Questions
- Topic: Extruder wont extrude Hitop 3DP12
- Replies: 38
- Views: 45701
Re: Extruder wont extrude Hitop 3DP12
Yep your correct. Great eyes you have. Nozel was jammed with plastic I think the Teflon tube was installed upside down.
I have a new heater but it wont heat. Had to wire up to my connector. Are the extruder heater or temp sensor polarized. + or - I see no markings?
I have a new heater but it wont heat. Had to wire up to my connector. Are the extruder heater or temp sensor polarized. + or - I see no markings?
- December 31st, 2018, 1:16 pm
- Forum: General Questions
- Topic: Extruder wont extrude Hitop 3DP12
- Replies: 38
- Views: 45701
Re: Extruder wont extrude Hitop 3DP12
OK, here it is. I used your setting Hictop 1.75 Profiles 20.ini
Printer was set up on a card table, not sure if that was the most stable spot.
Thanks,
Brian
Printer was set up on a card table, not sure if that was the most stable spot.
Thanks,
Brian
- December 30th, 2018, 8:13 pm
- Forum: General Questions
- Topic: Extruder wont extrude Hitop 3DP12
- Replies: 38
- Views: 45701
Re: Extruder wont extrude Hitop 3DP12
WORKING!
Was a bad stepper. First print not so nice a few blobs?
Was a bad stepper. First print not so nice a few blobs?
- December 22nd, 2018, 6:19 pm
- Forum: General Questions
- Topic: Extruder wont extrude Hitop 3DP12
- Replies: 38
- Views: 45701
Re: Extruder wont extrude Hitop 3DP12
Your settings no joy. Trying to move extruder with Move Axis control, nothing. Will try swapping some motor connections.
- December 22nd, 2018, 5:57 pm
- Forum: General Questions
- Topic: Extruder wont extrude Hitop 3DP12
- Replies: 38
- Views: 45701
Re: Extruder wont extrude Hitop 3DP12
I'm using 1.7mm PLA .4 noz. and it oozes fine when pushed manually. I'll try your settings next
- December 22nd, 2018, 5:56 pm
- Forum: General Questions
- Topic: Extruder wont extrude Hitop 3DP12
- Replies: 38
- Views: 45701
Re: Extruder wont extrude Hitop 3DP12
Ok, measuring across these pins on the POT
I get 0.65 to 0.68 on all of the pots???
I get 0.65 to 0.68 on all of the pots???
- December 22nd, 2018, 10:45 am
- Forum: General Questions
- Topic: Extruder wont extrude Hitop 3DP12
- Replies: 38
- Views: 45701
Re: Extruder wont extrude Hitop 3DP12
Really good instructions. What pins do I check the stepper current? And your numbers are volts, do you mean amps?
- December 21st, 2018, 8:45 pm
- Forum: General Questions
- Topic: Extruder wont extrude Hitop 3DP12
- Replies: 38
- Views: 45701
Extruder wont extrude Hitop 3DP12
Hello, I'm at my wits end my Hictop 3DP12 wont print. When printing the motor on the extruder just moves forward one tooth's distance and back one tooth's distance back and forth. The nozzle is up to temp and not clogged I can push filament trough it fine. I have replaced the motor, the wires, and t...