GrueMaster - Thanks for the reply.
As the SUNLU Filament Dryer is working I also have bought plastic food containers with a lid that seals from the grocery shop.
I have put the desiccant packs in the containers so I guess I am all set now for some good printing.
Search found 42 matches
- September 29th, 2021, 8:58 am
- Forum: General 3D Printing Conversation
- Topic: Old Brittle Filament
- Replies: 10
- Views: 14435
- September 14th, 2021, 9:28 pm
- Forum: General 3D Printing Conversation
- Topic: Old Brittle Filament
- Replies: 10
- Views: 14435
Re: Old Brittle Filament
Thanks for the reply Lez0. Just a bit slow at seeing it. Just to update this thread about Brittle Filament, following is what I posted in SUNLU Filament Dryer S1 thread started on 28 December 2020. "Yahoo. The Sunlu actually works. I put it on for 6 hours at 55 degrees centigrade. It may not ne...
- July 28th, 2021, 10:40 am
- Forum: General 3D Printing Conversation
- Topic: 3dLAC Smells a lot
- Replies: 2
- Views: 3006
Re: 3dLAC Smells a lot
Thanks
- July 23rd, 2021, 11:44 pm
- Forum: General 3D Printing Conversation
- Topic: 3dLAC Smells a lot
- Replies: 2
- Views: 3006
3dLAC Smells a lot
I bought 3DLAC spray to use on my glass bed. I soon worked out not to put too much on because if I do I have to use a hammer to get prints off. Also tried the 50% alcohol and water but that does not seem to work on big prints but it must help. 3DLAC is much better to use than wood glue as there is v...
- July 11th, 2021, 10:01 pm
- Forum: General 3D Printing Conversation
- Topic: SUNLU Filament Dryer S1
- Replies: 13
- Views: 8011
Re: SUNLU Filament Dryer S1
My LCD is not faint as it has a bright backlight.
Your backlight must not be working.
Your backlight must not be working.
- July 11th, 2021, 9:45 am
- Forum: General 3D Printing Conversation
- Topic: SUNLU Filament Dryer S1
- Replies: 13
- Views: 8011
Re: SUNLU Filament Dryer S1
Yahoo. The Sunlu actually works. I put it on for 6 hours at 55 degrees centigrade. It may not need that long. Before I did the filament I could bend it once and it would break. After heating it, I just bent some over 40 times before it broke. I just bent over some twice and first time broke at 15 be...
- July 10th, 2021, 10:55 am
- Forum: General 3D Printing Conversation
- Topic: SUNLU Filament Dryer S1
- Replies: 13
- Views: 8011
Re: SUNLU Filament Dryer S1
Thanks. I have some brittle filament so will try it in the Sunlu but I bet it will still be brittle.
- July 8th, 2021, 10:04 am
- Forum: General 3D Printing Conversation
- Topic: SUNLU Filament Dryer S1
- Replies: 13
- Views: 8011
Re: SUNLU Filament Dryer S1
But is it still brittle and break easily after drying in the Print Dry Pro?
- July 4th, 2021, 1:07 am
- Forum: General 3D Printing Conversation
- Topic: SUNLU Filament Dryer S1
- Replies: 13
- Views: 8011
Re: SUNLU Filament Dryer S1
Still wondering with a good dryer does brittle filament come out not brittle?
- December 28th, 2020, 9:35 pm
- Forum: General 3D Printing Conversation
- Topic: SUNLU Filament Dryer S1
- Replies: 13
- Views: 8011
Re: SUNLU Filament Dryer S1
That one does look a lot better with a double wall, two rolls etc.
- December 28th, 2020, 9:32 pm
- Forum: General 3D Printing Conversation
- Topic: Old Brittle Filament
- Replies: 10
- Views: 14435
Re: Old Brittle Filament
Roberts_Clif My filament is about the same age as yours and a couple break if I leave them in the printer over night but do not break when I use them. I just bought a SUNLU Filament Dryer S1 and started a new post as this post was getting old and not many comments. In that post I asked does a filame...
- December 28th, 2020, 7:45 am
- Forum: General 3D Printing Conversation
- Topic: Old Brittle Filament
- Replies: 10
- Views: 14435
Re: Old Brittle Filament
Thanks for the reply. Sorry I did not see your reply earlier.
- December 28th, 2020, 7:43 am
- Forum: General 3D Printing Conversation
- Topic: SUNLU Filament Dryer S1
- Replies: 13
- Views: 8011
SUNLU Filament Dryer S1
I bought a SUNLU Filament Dryer S1 and put some brittle filement in it at 50degrees centigrade for 6 hours and the filament was still brittle and broke easy.
I guess a Filament Dryer does not fix brittle filament?
I guess a Filament Dryer does not fix brittle filament?
- July 9th, 2020, 4:13 am
- Forum: General 3D Printing Conversation
- Topic: Old Brittle Filament
- Replies: 10
- Views: 14435
Re: Old Brittle Filament
1800 views and no comments seems strange.
Just wondered what the disadvantages are in using old brittle filament? Maybe none.
Just wondered what the disadvantages are in using old brittle filament? Maybe none.
- April 27th, 2020, 1:09 am
- Forum: General 3D Printing Conversation
- Topic: Old Brittle Filament
- Replies: 10
- Views: 14435
Old Brittle Filament
I understand that old brittle filament can be put in an oven to dry it out but wondered if the prints from brittle filament is worse than with new filament.
I can not tell as most of mine have a rough surface. Some are quite good. But wondered if the prints are better with new filament?
Thanks
I can not tell as most of mine have a rough surface. Some are quite good. But wondered if the prints are better with new filament?
Thanks