Search found 29 matches
- July 14th, 2019, 4:23 am
- Forum: General 3D Printing Conversation
- Topic: Print used for "lost foam casting" ???
- Replies: 2
- Views: 3956
Print used for "lost foam casting" ???
Do any of you have exparience - no guessing - experience with filament material that can be used for this casting method ? I want to make a casting in brass or bronce of a very, very indented and detailed object - I'm NOT able to use ordinary method with 2-3 part form - I have to use "lost foam...
- July 12th, 2019, 9:43 am
- Forum: General 3D Printing Conversation
- Topic: Suddenly very bad printing ??
- Replies: 8
- Views: 7720
Re: Suddenly very bad printing ??
Oh, it's way worse than I first thought ! This banking noise kept on ! I then disassambled the hot end ... and there is was ... it was NOT and has NEVER been assembled correctly - where is the QC at Creality ... I beleave NON excisting ! The filament hose ended 15mm abowe the nozzle and there was th...
- July 10th, 2019, 11:31 am
- Forum: Electronics
- Topic: LED lights on the CR10s PRO ?
- Replies: 1
- Views: 7739
Re: LED lights on the CR10s PRO ?
None knows anything at all ? Now I got 4 white LEDs mounted in a printed bracket around the nozzle, driven by a constant current sink 20mA and cable along the filament hose to an external power suply - it works nicely ! Now I just need to find a method to get the cable from the gantry to the base bo...
- July 8th, 2019, 11:09 am
- Forum: Electronics
- Topic: LED lights on the CR10s PRO ?
- Replies: 1
- Views: 7739
LED lights on the CR10s PRO ?
Someone here that knows if any of the UN-used plugs on the plugboard (behind where the ribbon cable is connected to tha gantry) can be used for switching 4 LEDs ON/OFF from a switch I mount beside be screen ? I assume there is some power to get inside (only <=100 mA) it could be nicer instead of hav...
- July 8th, 2019, 4:03 am
- Forum: General 3D Printing Conversation
- Topic: LEDs to light up the nozzle on a CR10s PRO ??
- Replies: 1
- Views: 2798
LEDs to light up the nozzle on a CR10s PRO ??
I have a CR10s PRO and I thought I had fastened ALL screws but ... oh, I missed the one holding the spring loaded lever for the filament feeder and it got loose and nearly fell off ! Now that I have a breakdown and the X-grantry apart because of loose screws all over I want to design a frame/brachet...
- July 7th, 2019, 4:18 pm
- Forum: General 3D Printing Conversation
- Topic: Suddenly very bad printing ??
- Replies: 8
- Views: 7720
Re: Suddenly very bad printing ??
No, but I found the fault - the feeder wheel was loosy goosy and nearly falling of so not enough filament was fed into the extruder
- July 7th, 2019, 11:51 am
- Forum: General 3D Printing Conversation
- Topic: Suddenly very bad printing ??
- Replies: 8
- Views: 7720
Re: Suddenly very bad printing ??
I think you missed, that ONLY the dimensions has changed between the two printouts - NO change in settings at all !
What is this "mesh cleaning" program ?
What is this "mesh cleaning" program ?
- July 7th, 2019, 12:54 am
- Forum: General 3D Printing Conversation
- Topic: Suddenly very bad printing ??
- Replies: 8
- Views: 7720
Suddenly very bad printing ??
I made up a bracket in Fusion 360 for protecting the USB and SD-card on a CR10s PRO. The first print looked very nice but the dimemsions had to be a little different. I made the changes in the dimensions and did another print and it looked like _BEEP_ ! I even made a new drawing from scratch with th...
- June 16th, 2019, 11:26 am
- Forum: General 3D Printing Conversation
- Topic: Support not supporting anything ??
- Replies: 6
- Views: 6275
Re: Support not supporting anything ??
Now I found a video on YouTube explaining a little of the Cura settings - but I still don't get it right ... Cure shows exactly the support where you would exspect it by the red color. take a look here - it's red too on the similar faces in the symmetry. https://1drv.ms/u/s!Ap0XTBN0ykvEhKxUL19pBDPwm...
- June 16th, 2019, 7:51 am
- Forum: General 3D Printing Conversation
- Topic: Support not supporting anything ??
- Replies: 6
- Views: 6275
Re: Support not supporting anything ??
Have you reported it to Cura? Lez I don't think it's a Cura problem ... I think it's me the novice :lol: I loose way too much time and material on printing supports that are 1) way too "heavy duty" 2) sometimes not even touching the model If I look at the test file from Creality (Test-dog...
- June 15th, 2019, 2:05 pm
- Forum: General 3D Printing Conversation
- Topic: Support not supporting anything ??
- Replies: 6
- Views: 6275
Re: Support not supporting anything ??
No one have any ideas ?
- June 15th, 2019, 3:01 am
- Forum: General 3D Printing Conversation
- Topic: Support not supporting anything ??
- Replies: 6
- Views: 6275
Support not supporting anything ??
I am new to the 3D printing and I have a Fusion360, Cura 4.1.0 and CR10s PRO as the work flow. My model is symmetric but is supported differently eventhough the shapes are the same - some of the supports don't even touch the model ???? How can I delete the support that's not touching my model and wh...
- June 13th, 2019, 1:22 pm
- Forum: General 3D Printing Conversation
- Topic: Novice CR10s PRO CURA 4 user - direct print ??
- Replies: 5
- Views: 5473
Re: Novice CR10s PRO CURA 4 user - direct print ??
I love Occams Razor ... an old version of KIS )
- June 13th, 2019, 7:55 am
- Forum: General 3D Printing Conversation
- Topic: Novice CR10s PRO CURA 4 user - direct print ??
- Replies: 5
- Views: 5473
Novice CR10s PRO CURA 4 user - direct print ??
I have set up my printer and it works nicely. I tested it with printing from the SC-Card - with the test-Dog from Creality and a box I made myself. I want to be able to print DIRECLY from Cura to the printer, and it kind of works but not quite. When I have prepared the files I can click a button &qu...