Search found 1372 matches

by Roberts_Clif
August 22nd, 2022, 12:59 pm
Forum: Cura
Topic: Stinging
Replies: 14
Views: 4473

Re: Stinging

Sorry to hear this. I found that PrusaSlicer works so well that in my opinion it was well worth this simple conversion effort.

Still use Cura on many projects though in some special cases prefer using PrusaSlicer.
I came into this 3D Printing as a hobby to learn all I could.
by Roberts_Clif
August 19th, 2022, 7:30 pm
Forum: Cura
Topic: Stinging
Replies: 14
Views: 4473

Re: Stinging

I have multiple configurations for ABS and PLA Filament. And even though all three of my 3D Printers are the same for my Hictop Profiles You can see I have a few one for Each of my Octoprint modules. And a couple for Each of My model Hictops 3DP11 and a 3DP12. Actually guess have a lot more individu...
by Roberts_Clif
August 19th, 2022, 8:33 am
Forum: Cura
Topic: Stinging
Replies: 14
Views: 4473

Re: Stinging

This has to be difficult as TPU as I have heard is famous to stringing. Would you be in for a slicer change that I have thought was one of the best free slicer ever. If so Try Prusa slicer It has a web link to several 3D Printer configurations an a custom configuration. I start with a Ender 3 Config...
by Roberts_Clif
July 29th, 2022, 2:49 pm
Forum: General Questions
Topic: Is there anybody out there?
Replies: 14
Views: 8395

Re: Is there anybody out there?

The dimple is a great Ideal

I am using a simple cheap bed surface purchased form China.

I have enabled S-Curves which calm down down the 3D Printer a bit.
by Roberts_Clif
July 29th, 2022, 7:59 am
Forum: General Questions
Topic: Is there anybody out there?
Replies: 14
Views: 8395

Re: Is there anybody out there?

I noticed that my heat block was askew. I went to investigate by touching it and it was LOOSE!! That could very well be the reason why all of my prints with the 4 bearing setup failed miserably. I'd like to see a diagram to see what the clearance should be from the threaded metal tube to the feed a...
by Roberts_Clif
July 28th, 2022, 9:07 pm
Forum: General Questions
Topic: Is there anybody out there?
Replies: 14
Views: 8395

Re: Is there anybody out there?

I will update you on any changes I make for the BL touch and post them here. I'll likely work with your information to get it working. I must say again - your information spread throughout this forum is superb. Sometimes one has to read a bit before that information is revealed, but it's a decent a...
by Roberts_Clif
July 28th, 2022, 7:34 am
Forum: General Questions
Topic: Is there anybody out there?
Replies: 14
Views: 8395

Re: Is there anybody out there?

Yes I have all my Hictop custom versions of Marlin archived an can flash at will to any version wanting to test. I have flashed my 3D Printers to test problems others were having with a version to see if I could duplicate there problems & Correct. No I do not have a BL tough. I have a 3D Touch s...
by Roberts_Clif
July 27th, 2022, 7:38 pm
Forum: General Questions
Topic: Is there anybody out there?
Replies: 14
Views: 8395

Re: Is there anybody out there?

I have flashed most versions of Marlin 1.x.x thru Marlin 2.0.9.2 had a minor problems using Marlin 2.0.9.3 so reverted to 2.0.9.2 on my Hictops.
by Roberts_Clif
July 27th, 2022, 7:20 am
Forum: General Questions
Topic: Is there anybody out there?
Replies: 14
Views: 8395

Re: Is there anybody out there?

I have been using 4 Bearing on all three of my Hictop Printers with no problems, wonder why you are having problems? Would like to see your upgraded Base plate, please post more information. I Have firmware changes for BL Touch though it has never been tested would like to see your firmware changes....
by Roberts_Clif
July 26th, 2022, 8:19 pm
Forum: General Questions
Topic: Is there anybody out there?
Replies: 14
Views: 8395

Re: Is there anybody out there?

Yes.
by Roberts_Clif
July 15th, 2022, 9:18 am
Forum: Software and Firmware Discussion
Topic: Marlin manual Bed leveling Leveling increment tweaking
Replies: 10
Views: 19124

Re: Marlin manual Bed leveling Leveling increment tweaking

SNo4 Proximity Sensor Mount here

I have designed a mount for Omron TL-W3MC2 attached, was looking here could not find my post so re-posted link
New Hictop Sensor Mount v2.stl
(35.92 KiB) Downloaded 153 times
New Hictop Sliding connector.stl
(31.43 KiB) Downloaded 151 times
by Roberts_Clif
June 28th, 2022, 12:07 pm
Forum: Cura
Topic: Pause a print in Cura
Replies: 15
Views: 5818

Re: Pause a print in Cura

OK,

It was the version of firmware and not the lines that were enabled.
by Roberts_Clif
June 27th, 2022, 8:51 pm
Forum: Cura
Topic: Pause a print in Cura
Replies: 15
Views: 5818

Re: Pause a print in Cura

Well that is strange, when use the script pause at height stops until I press a key to continue.

I wonder if enabling the code below changed the way my pause works.

Code: Select all

#define FILAMENT_RUNOUT_SENSOR
#define ADVANCED_PAUSE_FEATURE
#define PARK_HEAD_ON_PAUSE  // this one
by Roberts_Clif
June 27th, 2022, 5:36 am
Forum: Cura
Topic: Pause a print in Cura
Replies: 15
Views: 5818

Re: Pause a print in Cura

Where To Find The Feature – Cura Pause at Height / Layer

An in an older version of Cura below
Cura 15.04.6.jpg
Cura 15.04.6.jpg (8.43 KiB) Viewed 3712 times
by Roberts_Clif
June 26th, 2022, 8:28 pm
Forum: Cura
Topic: Pause a print in Cura
Replies: 15
Views: 5818

Re: Pause a print in Cura

I have always used a simple pause at height using Cura works in all versions.

Have also used a pause at layer height in Prusa slicer it works just as well.

Go to advanced search