This just keeps getting more complicated. Fun
So now to sort out your wiring changes
Search found 3966 matches
- May 21st, 2016, 11:14 am
- Forum: Ultimaker Original & Ultimaker Original +
- Topic: Fan shroud upgrade
- Replies: 333
- Views: 276272
- May 20th, 2016, 10:29 pm
- Forum: Ultimaker Original & Ultimaker Original +
- Topic: Fan shroud upgrade
- Replies: 333
- Views: 276272
Re: Fan shroud upgrade
Well I was noticing the temperature was wandering all over the place first. I removed the shroud and widened the hole IMG_2563.JPG Mounted IMG_2564.JPG I installed Amadee's firmware as well, that was painless. I'm wondering about the fan kick start tho. Since we know my fans are pretty powerful, in ...
- May 20th, 2016, 10:06 pm
- Forum: Firmware
- Topic: UMO / UMO+ Firmware
- Replies: 275
- Views: 267538
Re: UMO / UMO+ Firmware
So I am using this and wonder, is there a 'stall speed' of sorts? Since my fans have so much force, in Cura I set min to 3% and max to 4%. When the print does the first layer with fans, they puff up then I get max temp error. I tried moving the max up a bit more, same result. I'll post a video in th...
- May 20th, 2016, 9:14 pm
- Forum: Firmware
- Topic: UMO / UMO+ Firmware
- Replies: 275
- Views: 267538
Re: UMO / UMO+ Firmware
Installed the firmware for my UMO + Heated bed, with the fan kick
Looking forward to trying!
Looking forward to trying!
- May 20th, 2016, 5:35 pm
- Forum: Ultimaker Original & Ultimaker Original +
- Topic: Fan shroud upgrade
- Replies: 333
- Views: 276272
Re: Fan shroud upgrade
I am noticing the beep on the Ulticontroller sounds different when the fans run (even low). Anyone else get that?
- May 20th, 2016, 5:33 pm
- Forum: Ultimaker Original & Ultimaker Original +
- Topic: Fan shroud upgrade
- Replies: 333
- Views: 276272
Re: Fan shroud upgrade
And a little foil tape to protect the wires near the print head
And print head clearance
And print head clearance
- May 20th, 2016, 5:23 pm
- Forum: Ultimaker Original & Ultimaker Original +
- Topic: Fan shroud upgrade
- Replies: 333
- Views: 276272
Re: Fan shroud upgrade
Some wire work...
- May 20th, 2016, 3:23 pm
- Forum: Cura
- Topic: Cura 2.1 open beta
- Replies: 83
- Views: 76943
Re: Cura 2.1 open beta
I've stuck to 15.04
- May 20th, 2016, 3:22 pm
- Forum: Ultimaker Original & Ultimaker Original +
- Topic: Fan shroud upgrade
- Replies: 333
- Views: 276272
Re: Fan shroud upgrade
Well a Facebook friend made a suggestion...remove the shrinktubing, twist the wires up...then (I guess), use electrical tape to hold it all together?
- May 20th, 2016, 2:45 pm
- Forum: Ultimaker Original & Ultimaker Original +
- Topic: Fan shroud upgrade
- Replies: 333
- Views: 276272
Re: Fan shroud upgrade
Were you able to do that without fan or minimal?Amedee wrote:Print came OK, now it's the matter of putting everything together and see how it goes with nGen...
Not a bad print
- May 20th, 2016, 2:32 pm
- Forum: Firmware
- Topic: UMO / UMO+ Firmware
- Replies: 275
- Views: 267538
Re: UMO / UMO+ Firmware
Now what could've brought that on
I believe...on my fans, they start at 1% on the Ulticontroller. I see the Fan Kickstart...and thinking this could be useful.
I believe...on my fans, they start at 1% on the Ulticontroller. I see the Fan Kickstart...and thinking this could be useful.
- May 20th, 2016, 2:24 pm
- Forum: Ultimaker Original & Ultimaker Original +
- Topic: Fan shroud upgrade
- Replies: 333
- Views: 276272
Re: Fan shroud upgrade
I have a dumb question....(you see if I preface with that, you guys all smile!)
The wiring from the fan...should I replace that with some shielded/twisted wire instead of the stranded wire that is in there?
Just trying to solve the PWM noise issue!
The wiring from the fan...should I replace that with some shielded/twisted wire instead of the stranded wire that is in there?
Just trying to solve the PWM noise issue!
- May 20th, 2016, 11:25 am
- Forum: Ultimaker Original & Ultimaker Original +
- Topic: Fan shroud upgrade
- Replies: 333
- Views: 276272
Re: Fan shroud upgrade
Umm. There's only one posible orientation if the hotend it's on the front right. The top left/right 3point reference marks where it goes the hotend. So, how can it be installed otherway? Edit: There's also rotating view of the fancap assembled. Well just ideas...if you want to leave it be, that's u...
- May 20th, 2016, 10:35 am
- Forum: Ultimaker Original & Ultimaker Original +
- Topic: Fan shroud upgrade
- Replies: 333
- Views: 276272
Re: Fan shroud upgrade
Well let's see if we can make what we have work first. We've got a lot of hours into this and I'd hate to give up so soon Also, if you want to make some changes on your shroud document on Ultimaker...I would suggest more side pictures that detail to order of assembly. The animated one shows from a h...
- May 20th, 2016, 10:15 am
- Forum: Ultimaker Original & Ultimaker Original +
- Topic: Fan shroud upgrade
- Replies: 333
- Views: 276272
Re: Fan shroud upgrade
Neo....I know you love to experiment.... ...But I am desperately way behind in printing my BB-8 project. I have spent so much time chasing down problems (heated bed upgrade with complications, belt/pulley issues, etc) that I have little to show for progress. Honestly, if I were to invest any more mo...