Cura 3.0 beta

Discussion of Ultimaker's open-source Cura software
Post Reply
nallath
Reactions:
Posts: 247
Joined: February 16th, 2016, 3:12 am
3D Printer(s): Ultimaker

Cura 3.0 beta

Post by nallath » October 11th, 2017, 5:27 pm

It's a bit of a silent beta, but it's there;
https://ultimaker.com/en/community/5144 ... ura-3-beta

GrueMaster
Reactions:
Posts: 148
Joined: March 15th, 2017, 8:46 pm
Location: Oregon
3D Printer(s): HICTOP 3DP-17

Re: Cura 3.0 beta

Post by GrueMaster » October 12th, 2017, 2:40 am

On it. Will deep dive this weekend to see what issues I can find (unless I am drug away from my 3D printer, kicking and screaming).

User avatar
darkdvd
Reactions:
Posts: 49
Joined: February 27th, 2016, 6:01 am
Location: France
3D Printer(s): UM2/UM2+

Re: Cura 3.0 beta

Post by darkdvd » October 12th, 2017, 5:34 am

No "Infill Slider", nallath ?
"Qui ne connaît pas l'histoire ne connaît rien"
Edward johnston, 1990

User avatar
LePaul
Reactions:
Posts: 2782
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, Folger Tech FT-5, Creality CR-10
Contact:

Re: Cura 3.0 beta

Post by LePaul » October 12th, 2017, 9:34 am

Downloading 3.0.1 Win64 Beta now :)

nallath
Reactions:
Posts: 247
Joined: February 16th, 2016, 3:12 am
3D Printer(s): Ultimaker

Re: Cura 3.0 beta

Post by nallath » October 12th, 2017, 1:23 pm

darkdvd wrote:
October 12th, 2017, 5:34 am
No "Infill Slider", nallath ?
It's only in recommended.

User avatar
darkdvd
Reactions:
Posts: 49
Joined: February 27th, 2016, 6:01 am
Location: France
3D Printer(s): UM2/UM2+

Re: Cura 3.0 beta

Post by darkdvd » October 12th, 2017, 1:38 pm

?
"Qui ne connaît pas l'histoire ne connaît rien"
Edward johnston, 1990

User avatar
darkdvd
Reactions:
Posts: 49
Joined: February 27th, 2016, 6:01 am
Location: France
3D Printer(s): UM2/UM2+

Re: Cura 3.0 beta

Post by darkdvd » October 12th, 2017, 3:10 pm

Ok ! nallath, I am asking for "Infill Shift" not "Infill Slider" function in recommended mode...
"Qui ne connaît pas l'histoire ne connaît rien"
Edward johnston, 1990

nallath
Reactions:
Posts: 247
Joined: February 16th, 2016, 3:12 am
3D Printer(s): Ultimaker

Re: Cura 3.0 beta

Post by nallath » October 16th, 2017, 8:26 am

oh euh. Could be that it didn't make it in time for 3.0. Not a 100% sure.

Post Reply

Return to “Cura”

Who is online

Users browsing this forum: No registered users and 1 guest