Marlin manual Bed leveling Leveling increment tweaking
-
- Reactions:
- Posts: 2
- Joined: February 24th, 2020, 10:53 am
- 3D Printer(s): Maker Farm Pegasus 8 & 12
Marlin manual Bed leveling Leveling increment tweaking
Using a Makerfarm Pegasus 8 which in turn is Using Marlin Firmware 1.x, trying to improve my accuracy and was wondering if there is a way to tweak my setting for the manual leveling process.
When performing a manual bed level, when i turn the knob the x carriage moves up or down at .5mm increments (I think) is there anyway i can lower the number to .25mm or .1mm.
Perhaps I'm being anal, but I like to be as close to possible when running the process.
Thanks
When performing a manual bed level, when i turn the knob the x carriage moves up or down at .5mm increments (I think) is there anyway i can lower the number to .25mm or .1mm.
Perhaps I'm being anal, but I like to be as close to possible when running the process.
Thanks
- Roberts_Clif
- Reactions:
- Posts: 1384
- Joined: March 25th, 2017, 8:17 am
- Location: Washington, State USA
- 3D Printer(s): Hictop 3DP11/12
Re: Marlin manual Bed leveling Leveling increment tweaking
Are you looking for
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
#define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
-
- Reactions:
- Posts: 2
- Joined: February 24th, 2020, 10:53 am
- 3D Printer(s): Maker Farm Pegasus 8 & 12
Re: Marlin manual Bed leveling Leveling increment tweaking
Perhaps, is this line already in the Marlin Config.h or am I adding it? Conversely is there a way to do it via Pronterface and gcode commands?
- Roberts_Clif
- Reactions:
- Posts: 1384
- Joined: March 25th, 2017, 8:17 am
- Location: Washington, State USA
- 3D Printer(s): Hictop 3DP11/12
Re: Marlin manual Bed leveling Leveling increment tweaking
I found it in all versions of marlin 1.1.x that I have programmed for My 3D Printers.
I do not know of a way maybe, someone else will know.
I do not know of a way maybe, someone else will know.
-
- Reactions:
- Posts: 74
- Joined: January 1st, 2018, 11:02 am
- 3D Printer(s): hictop auto leveling desktop 3d printer prusa i3
Re: Marlin manual Bed leveling Leveling increment tweaking
If its of any use I redesigned an Auto Bed Leveling Sensor Mount. Unlike the 3 part assembly thats on Thingiverse, my one is only a two part and fits the linear bearing housing perfectly.
If I get the time I guess I should upload the files onto Thingiverse as its easy to fit and adjust.
If I get the time I guess I should upload the files onto Thingiverse as its easy to fit and adjust.
- GrueMaster
- Reactions:
- Posts: 522
- Joined: March 15th, 2017, 8:46 pm
- Location: Oregon
- 3D Printer(s): Hictop 3DP-17, Hictop CR-10S
Re: Marlin manual Bed leveling Leveling increment tweaking
You can also post a picture here.
Re: Marlin manual Bed leveling Leveling increment tweaking
The print beds on 3D printers aren’t always perfectly flat. Sometimes you can get lucky and get a pefectly flat surface to print on, but considering the materials the bed is made out of and the constantJT whatsapp heat cycling, it’s more likely that you’ll have to deal with at least some warping.
Mesh Bed Leveling
There are few options for compensating for a warped bed, but I chose to use Mesh Bed Leveling because it didn’t require any extra hardware or tools.
This does require building a custom configuration for Marlin.
At a minimum, enable mesh bed leveling in Configuration.h:
Mesh Bed Leveling
There are few options for compensating for a warped bed, but I chose to use Mesh Bed Leveling because it didn’t require any extra hardware or tools.
This does require building a custom configuration for Marlin.
At a minimum, enable mesh bed leveling in Configuration.h:
Re: Marlin manual Bed leveling Leveling increment tweaking
Can we get the link please?Mr SNG wrote: ↑June 4th, 2020, 7:06 am If its of any use I redesigned an Auto Bed Leveling Sensor Mount. Unlike the 3 part assembly thats on Thingiverse, my one is only a two part and fits the linear bearing housing perfectly.
WhatsApp Aero APK
If I get the time I guess I should upload the files onto Thingiverse as its easy to fit and adjust.
- Roberts_Clif
- Reactions:
- Posts: 1384
- Joined: March 25th, 2017, 8:17 am
- Location: Washington, State USA
- 3D Printer(s): Hictop 3DP11/12
Re: Marlin manual Bed leveling Leveling increment tweaking
SNo4 Proximity Sensor Mount here
I have designed a mount for Omron TL-W3MC2 attached, was looking here could not find my post so re-posted link
I have designed a mount for Omron TL-W3MC2 attached, was looking here could not find my post so re-posted link
Re: Marlin manual Bed leveling Leveling increment tweaking
Specifically, you have to make sure the frame is rigid, especially the portion that supports the Y axis guide rails, and use a flat plate.Stephen21 wrote: ↑July 14th, 2022, 10:02 amCan we get the link please?Mr SNG wrote: ↑June 4th, 2020, 7:06 am If its of any use I redesigned an Auto Bed Leveling Sensor Mount. Unlike the 3 part assembly thats on Thingiverse, my one is only a two part and fits the linear bearing housing perfectly.
If I get the time I guess I should upload the files onto Thingiverse as its easy to fit and adjust.
-
- Reactions:
- Posts: 1
- Joined: August 21st, 2023, 11:39 am
- 3D Printer(s): Ultimaker
Re: Marlin manual Bed leveling Leveling increment tweaking
I will suggest you adjust the probe points, select the bed leveling method, and give access to the configuration. I think this will work enough.
Youtube Vanced APK
Youtube Vanced APK