Zero Gravity Direct Drive Extruder

Discussions concerning the Ultimaker 2 / Ultimaker 2+ series of printers, including the Ultimaker 2 Go
User avatar
Neotko
Reactions:
Posts: 1142
Joined: February 7th, 2016, 7:02 pm
Location: Madrid
3D Printer(s): UMO+ x2.5
Contact:

Re: Zero Gravity Direct Drive Extruder

Post by Neotko »

Umm maybe I didn't understood. Photo? I'm too sleepy
User avatar
nilrog
Reactions:
Posts: 438
Joined: February 24th, 2016, 4:48 pm
Location: Örsundsbro, Sweden
3D Printer(s): UMO+

Re: Zero Gravity Direct Drive Extruder

Post by nilrog »

No, it's the spacer between the "yaw" and the part where you screw the stepper into. I tried to reference them above by their name in the zip-file ;)
User avatar
nilrog
Reactions:
Posts: 438
Joined: February 24th, 2016, 4:48 pm
Location: Örsundsbro, Sweden
3D Printer(s): UMO+

Re: Zero Gravity Direct Drive Extruder

Post by nilrog »

Maybe photo later today :p
User avatar
nilrog
Reactions:
Posts: 438
Joined: February 24th, 2016, 4:48 pm
Location: Örsundsbro, Sweden
3D Printer(s): UMO+

Re: Zero Gravity Direct Drive Extruder

Post by nilrog »

It's one of the parts named "FLEX" that is part of the Nema17 zip even though you need it for the Bondtech.
User avatar
Neotko
Reactions:
Posts: 1142
Joined: February 7th, 2016, 7:02 pm
Location: Madrid
3D Printer(s): UMO+ x2.5
Contact:

Re: Zero Gravity Direct Drive Extruder

Post by Neotko »

Can you check with the full stl assembly ? I don't get it. Sorry I'm really dense atm
User avatar
nilrog
Reactions:
Posts: 438
Joined: February 24th, 2016, 4:48 pm
Location: Örsundsbro, Sweden
3D Printer(s): UMO+

Re: Zero Gravity Direct Drive Extruder

Post by nilrog »

NP, will check it tonight :)

I've only used the photos and files as base for my assembly so far. And for the temp PLA parts it was ok. But now when I'm replacing them with flexible parts it gets a bit confusing :P
User avatar
nilrog
Reactions:
Posts: 438
Joined: February 24th, 2016, 4:48 pm
Location: Örsundsbro, Sweden
3D Printer(s): UMO+

Re: Zero Gravity Direct Drive Extruder

Post by nilrog »

Ok, I was probably a bit confused, i'm down with a flu this weekend :( (the "man-cold" version :lol: )

I was referring to this yellow piece where the screws to the motor holder goes through:
zge_bontech.png
zge_bontech.png (62.45 KiB) Viewed 12751 times
And I though that the "Motor support damper-FLEX.stl" from the NEMA17 zip was this one...but I now see that it is the one that will hold the NEMA17 motor instead.

So I guess that the yellow part is this one, "Motor tilt spacer support-MEDQ.stl"?

It's slightly confusing since all the parts needed for the Bondtech geared version is not in the Bondtech package...while for the NEMA17 all files are there ;)

Anyway, I think i'm back on track now and will soon finish the Bondtech-Short version :)

(Although i'm still very impressed with the all-PLA version. I have had zero problems with it...and now I can easily print #filaflex with 40mm/s at 0.15 :) )
User avatar
Neotko
Reactions:
Posts: 1142
Joined: February 7th, 2016, 7:02 pm
Location: Madrid
3D Printer(s): UMO+ x2.5
Contact:

Re: Zero Gravity Direct Drive Extruder

Post by Neotko »

That yellow part is solid, not flex.
Post Reply

Return to “Ultimaker 2 / Ultimaker 2+ / Extended & Go”