Raise 3D
- Izzy
- Reactions:
- Posts: 604
- Joined: February 12th, 2016, 2:29 am
- Location: England
- 3D Printer(s): Ultimaker 2
Re: Raise 3D
I'm watching the OIO
- LePaul
- Reactions:
- Posts: 3974
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Re: Raise 3D
I've been reading their support forums...I figure if there are troubles, you can spot them there!
But from what I have seen of my friend's prints...wow. Just wow.
But from what I have seen of my friend's prints...wow. Just wow.
- Izzy
- Reactions:
- Posts: 604
- Joined: February 12th, 2016, 2:29 am
- Location: England
- 3D Printer(s): Ultimaker 2
Re: Raise 3D
I take it that's wow for the Raise 3D
- LePaul
- Reactions:
- Posts: 3974
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Re: Raise 3D
Poor guy is having troubles straight out of the box
- ivan.akapulko
- Reactions:
- Posts: 389
- Joined: February 11th, 2016, 11:27 am
- Location: Ust-Kamenogorsk, Kazakhstan
- 3D Printer(s): Ultimaker 2
- Contact:
Re: Raise 3D
Its looks like a epic f*ckup. No proper sd/usb reading, strange filament guide system (i really like, how its maded by BQ Witbox, for example). And this strange noise, when buildplate rises up to the nozzle....LePaul wrote:Poor guy is having troubles straight out of the box
- LePaul
- Reactions:
- Posts: 3974
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Re: Raise 3D
He posted an update, still lot's of problems
-
- Reactions:
- Posts: 4
- Joined: August 9th, 2016, 11:02 am
- 3D Printer(s): cel robox
Re: Raise 3D
I received my n2 last Tuesday and so far so good . I'm not very good with computers or software and it took me about 1 hour to go from out the box and printing my 1st model.
The quality of prints are really good
Theres next to no noise.
The control panel is great very easy to use.
Wifi was fast and easy to set up.
Using there own software to slice and that works very well had no issues .
Will post photos later
The quality of prints are really good
Theres next to no noise.
The control panel is great very easy to use.
Wifi was fast and easy to set up.
Using there own software to slice and that works very well had no issues .
Will post photos later
- LePaul
- Reactions:
- Posts: 3974
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Re: Raise 3D
Finally his review
- LePaul
- Reactions:
- Posts: 3974
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Re: Raise 3D
Came across this today