Hi !
Little problem with Tinker_16.01 firmaware on two UM2 : sometimes, the LCD freeze during print. button is working but the LCD is completly freeze.
Two times today on the two printers : one with a 3 hours print, one on a 13 hours print (oups).
During this time, the printers continue to print without problem....
David
(note : my french is better than my English...)
Tinker_16.01 problem
- darkdvd
- Reactions:
- Posts: 53
- Joined: February 27th, 2016, 6:01 am
- Location: France
- 3D Printer(s): UM2/UM2+
Re: Tinker_16.01 problem
Strange but the LCD screen is working now ! 07:29 left (freezing at 10:34 left)
- martin-bienz
- Reactions:
- Posts: 172
- Joined: February 22nd, 2016, 2:42 am
- Location: Switzerland
- 3D Printer(s): Ultimaker Original, prusa i3 mk2
Re: Tinker_16.01 problem
So it's probably a lcd update issue "only" as the printer continues to print? I am sure he will fix this
- darkdvd
- Reactions:
- Posts: 53
- Joined: February 27th, 2016, 6:01 am
- Location: France
- 3D Printer(s): UM2/UM2+
Re: Tinker_16.01 problem
This is not a big problem: the print ends perfectly, as an UMO without LCD PANEL!
- Neotko
- Reactions:
- Posts: 1142
- Joined: February 7th, 2016, 7:02 pm
- Location: Madrid
- 3D Printer(s): UMO+ x2.5
- Contact:
Re: Tinker_16.01 problem
Maybe it's cross talking. Separate the lcd cables and fix them a bit away with some blue tape.
- darkdvd
- Reactions:
- Posts: 53
- Joined: February 27th, 2016, 6:01 am
- Location: France
- 3D Printer(s): UM2/UM2+
Re: Tinker_16.01 problem
Same problem with two UM2 ?Neotko wrote:Maybe it's cross talking. Separate the lcd cables and fix them a bit away with some blue tape.
- Neotko
- Reactions:
- Posts: 1142
- Joined: February 7th, 2016, 7:02 pm
- Location: Madrid
- 3D Printer(s): UMO+ x2.5
- Contact:
Re: Tinker_16.01 problem
It happens sometimes on one of my umo+ (Same board different screen) screen banishes. But only sometimes (like one in a month). Much less since I separated the cables.
- darkdvd
- Reactions:
- Posts: 53
- Joined: February 27th, 2016, 6:01 am
- Location: France
- 3D Printer(s): UM2/UM2+
Re: Tinker_16.01 problem
OK, I understand.
I'll do a downgrade of firmware as a test, as requested me tinkergnome.
But for me, the same problem on two UM2, it's software, not hardware.
I'll do a downgrade of firmware as a test, as requested me tinkergnome.
But for me, the same problem on two UM2, it's software, not hardware.
- TinkerGnome
- Reactions:
- Posts: 8
- Joined: February 24th, 2016, 8:18 am
- 3D Printer(s): Ultimaker2
Re: Tinker_16.01 problem
It seems that it happens with the standard firmware too:
Screen/Input Freezing But Still Printing
...hmmmm rushour on the I2C bus...? Arduino experts present?
Screen/Input Freezing But Still Printing
...hmmmm rushour on the I2C bus...? Arduino experts present?