I am working on a 3 piece light saber shelf.
My neighbor approached me and ask if I could design a light saber shelf that she could use as a mold.
She will use the mold to be able to create many clear shelves, being clear she can then add glitter, sparkles, beads, stars or many other decorations.
As I believe she whats to sell them so cannot release the design.
What's everyone working on
- Roberts_Clif
- Reactions:
- Posts: 1385
- Joined: March 25th, 2017, 8:17 am
- Location: Washington, State USA
- 3D Printer(s): Hictop 3DP11/12
- GrueMaster
- Reactions:
- Posts: 522
- Joined: March 15th, 2017, 8:46 pm
- Location: Oregon
- 3D Printer(s): Hictop 3DP-17, Hictop CR-10S
Re: What's everyone working on
You may not be able to share the stl files, but you can share the final pictures and even a finished shelf. Helps promote her product.
- Roberts_Clif
- Reactions:
- Posts: 1385
- Joined: March 25th, 2017, 8:17 am
- Location: Washington, State USA
- 3D Printer(s): Hictop 3DP11/12
Re: What's everyone working on
I ask she said it was OK for me to { Post } As she was going to use what I 3D Printed for a Molding part.
Attached are the 3 Pieces of the Light Saber Shelf Molding Part.
The STL files are a fraction of the actual size, I expanded to the Max my 3D Printer would print for this customer.
Have fun if you decide to Print
Attached are the 3 Pieces of the Light Saber Shelf Molding Part.
The STL files are a fraction of the actual size, I expanded to the Max my 3D Printer would print for this customer.
Have fun if you decide to Print
- Attachments
-
- Top.stl
- (6.33 KiB) Downloaded 359 times
-
- Middle.stl
- (3.6 KiB) Downloaded 363 times
-
- Bottom.stl
- (48.71 KiB) Downloaded 367 times
- GrueMaster
- Reactions:
- Posts: 522
- Joined: March 15th, 2017, 8:46 pm
- Location: Oregon
- 3D Printer(s): Hictop 3DP-17, Hictop CR-10S
Re: What's everyone working on
Can't wait to see the final shelf. Not the print, but one of her finished units.
- Roberts_Clif
- Reactions:
- Posts: 1385
- Joined: March 25th, 2017, 8:17 am
- Location: Washington, State USA
- 3D Printer(s): Hictop 3DP11/12
Re: What's everyone working on
Then will ask her for a photo of the finished work and post it.
- LePaul
- Reactions:
- Posts: 3978
- Joined: February 7th, 2016, 10:26 pm
- Location: Bangor, Maine USA
- 3D Printer(s): 24 - Yes I have a problem!
- Contact:
Re: What's everyone working on
Well an ad appeared in my local Facebook Marketplace
Gentleman selling a new CR-10S. Just not his thing.
I really don't *need* a third one (or a 10th printer!) But...I couldn't pass up a good deal.
The print farm is getting a little bigger. I'll upgrade it to a Bondtech and not sure if I will do the DDS again or the DDX (BMG + Slice Mosquito)
I've been cranking out prints for my various projects and I keep getting asked for other parts. So the printers are certainly getting use!
I just really want to boost the safety aspect with some enclosures and venting/ductwork....plus fire supression.
Gentleman selling a new CR-10S. Just not his thing.
I really don't *need* a third one (or a 10th printer!) But...I couldn't pass up a good deal.
The print farm is getting a little bigger. I'll upgrade it to a Bondtech and not sure if I will do the DDS again or the DDX (BMG + Slice Mosquito)
I've been cranking out prints for my various projects and I keep getting asked for other parts. So the printers are certainly getting use!
I just really want to boost the safety aspect with some enclosures and venting/ductwork....plus fire supression.
- Roberts_Clif
- Reactions:
- Posts: 1385
- Joined: March 25th, 2017, 8:17 am
- Location: Washington, State USA
- 3D Printer(s): Hictop 3DP11/12
Re: What's everyone working on
Quite the Story @LePaul and still you got it!!!
I to work in this manner though running out of room a long time ago.
I to work in this manner though running out of room a long time ago.