Geeetech A10 3D Printer

Post Reply
User avatar
LePaul
Reactions:
Posts: 3200
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, FT-5, CR-10, CR-10S, Tevo Tornado
Contact:

Geeetech A10 3D Printer

Post by LePaul » November 3rd, 2018, 12:52 pm

A while ago, I was approached by Geeetech to take a look at their 3D Printers.

First, I am fascinated at the spelling of their name...so many E's!

Like most Chinese printers, it's largely a direct copy of something else...in this case, the Ender 3 (something I would be interested in checking out)

That said, they offered me a small discount from the $199 price tag to purchase one, try out and review.

It arrives next week and I am curious to see what it can do.

Print Volume is about the size of the Ultimaker (223 x 223 x 205 mm)...the A10 is 220 x 220 x 260

I'm curious if anyone has toyed with one yet? This one has a touch screen and wifi,

I'm hope the build quality is good.

Here's the link to Aliexpress for the make/model I picked up: https://www.aliexpress.com/store/produc ... _6047561.8

As my friend Tim Hoogland at TH3D mentioned to me recently, the frustrating thing with these printers from China is what is displayed on the order page can vary drastically from what you actually receive. He has purchased the same model printers a month apart and each have a wide variety of differences. Different setup of the rollers on the bed (staggered versus parallel), different hot ends and so on.

But at $199, it's pretty impressive to see where we are at the scale and size of printers in this price range from a year ago.

A year ago, a $200 printer would be a 4 inch by 4 inch print bed, no heated bed and probably something more of a novelty than a serious printer.

I'll let you guys know!

User avatar
LePaul
Reactions:
Posts: 3200
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, FT-5, CR-10, CR-10S, Tevo Tornado
Contact:

Re: Geeetech A10 3D Printer

Post by LePaul » November 9th, 2018, 9:18 am

Got the A10 unboxed and setup

A fairly simple affair, although a few things weren't well described...such as the z bearing/z screw guide that goes up top and how to secure the ribbon cable that goes from the controller to the 20 x 4 LCD screen.

The controller knob is a problem, it takes a lot of turns (5 or more) to move on level in the menus. So...setting the temps manually won't be a lot of fun with the stock firmware!

The bed surface isn't much to write home about. The glass bed is glued to the aluminum heated bed, so that'll be fun to pry apart to upgrade

With the electronics incorporated into the frame, it has pros and cons.

Pro... printer takes less space
Con... Getting access to the bed leveling knobs can be a challenge

I tend to run multiple skirts around my parts so I can crank the bed leveling knobs up and down as needed. With the electronics under the bed, it's tough to access the rear knobs.

It has a single Z screw and I checked the X gantry to make sure it was level, measuring the distance from x-gantry to bed. It looked good

The test print included on the SD card...and it takes full size SD cards (yay!)...is a dog test print. It sets the bed to 50C and PLA temp to 210. I found 50 to be too cool and I had part of the print lift a bit on the front.

But over all, a decent print.
a10.jpg
I'm going to upgrade the firmware with the Unified Firmware TH3D offers (and supports the A10)...that should resolve a few things

The print head has a mount for an auto bed leveling device, which I intend to use. TH3D is working on support for it (XY offset, etc).

The bed was a challenge to level and I wish this 4 point leveling would mimic the Ultimaker's 3 point leveling. It seems the rear of the bed is never quite right. When it is right, the center is too far from the nozzle.

More soon!

User avatar
Roberts_Clif
Reactions:
Posts: 488
Joined: March 25th, 2017, 8:17 am
Location: Washington
3D Printer(s): Hictop 3DP11/12

Re: Geeetech A10 3D Printer

Post by Roberts_Clif » November 9th, 2018, 4:51 pm

Where can I download the Dog.
Electronics Technician / Computer Programmer

User avatar
LePaul
Reactions:
Posts: 3200
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, FT-5, CR-10, CR-10S, Tevo Tornado
Contact:

Re: Geeetech A10 3D Printer

Post by LePaul » November 9th, 2018, 7:06 pm

Not sure, I just have the gcode on the SD card

User avatar
LePaul
Reactions:
Posts: 3200
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, FT-5, CR-10, CR-10S, Tevo Tornado
Contact:

Re: Geeetech A10 3D Printer

Post by LePaul » November 12th, 2018, 1:43 pm

Well...problems galore...

1) Bulge showing in one section of print, seems to indicate something is up with the z screw

2) Controller knob sucks. Dozens of turns to move through the menu items one by one. I'll have to remove the knob and see if that's any better.

3) Back cover for one of the rails came off in shipping. Not a big deal....just ugly.

4) Can't seem to connect via USB. Two different laptops, two different cables...right port, right baud rate..I mean, I've been connecting to printers for years. This one has something awry with it.

Worth $199? It's not looking like it. QA issues for sure.

User avatar
LePaul
Reactions:
Posts: 3200
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, FT-5, CR-10, CR-10S, Tevo Tornado
Contact:

Re: Geeetech A10 3D Printer

Post by LePaul » November 14th, 2018, 9:31 am

Well Geeetech's initial enthusiastic response to repair the printer has suddenly gone silent...so much for customer service

User avatar
LePaul
Reactions:
Posts: 3200
Joined: February 7th, 2016, 10:26 pm
Location: Bangor, Maine USA
3D Printer(s): Ultimaker 2+, FT-5, CR-10, CR-10S, Tevo Tornado
Contact:

Re: Geeetech A10 3D Printer

Post by LePaul » November 21st, 2018, 2:52 pm

Well....here's the latest


Post Reply

Return to “Other make/model 3D Printers!”